Kramers tricopter step by step: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| Line 13: | Line 13: | ||
- could glue | - could glue | ||
- zip tie in place | - zip tie in place | ||
- [[File: | - [[File:Kramers Tricopter Photo1.jpg|600px|thumb|left]] | ||
- Zip tie and connect speed control | - Zip tie and connect speed control | ||
- will need to determine direction after build by running the motor and noting direction so don't make permanent | - will need to determine direction after build by running the motor and noting direction so don't make permanent | ||
- | - [[File:Kramer's Tricopter Photo2.jpg|600px|thumb|left]] | ||
- drill and file 3D printed gimble mount | - drill and file 3D printed gimble mount | ||
- use a screw and glue the end to make gimble pivot | - use a screw and glue the end to make gimble pivot | ||
- | - [[File:Kramer's Tricopter Photo3.jpg|600px|thumb|left]] | ||
- use super glue | - use super glue | ||
- screw motor on 3D printed mount | - screw motor on 3D printed mount | ||
- may need to drill to fit | - may need to drill to fit | ||
- align wires away from base end | - align wires away from base end | ||
- | - [[File:Kramers Tricopter Photo4.jpg|600px|thumb|left]] | ||
- Attach servo | - Attach servo | ||
- use drill to reverse counter sink screw hole to get a flush connection | - use drill to reverse counter sink screw hole to get a flush connection | ||
| Line 30: | Line 31: | ||
- ensure full range of motion and attach star to servo | - ensure full range of motion and attach star to servo | ||
- superglue to gimble | - superglue to gimble | ||
- | - [[File:Kramers Tricopter Photo5.jpg|600px|thumb|left]] | ||
- Attach gimble and servo to leg | - Attach gimble and servo to leg | ||
- Found out I made a mistake in how the wires were aligned with cutout on leg | - Found out I made a mistake in how the wires were aligned with cutout on leg | ||
| Line 36: | Line 37: | ||
- use zip ties | - use zip ties | ||
- used super glue for spacer after zip tie | - used super glue for spacer after zip tie | ||
- | - [[File:Kramers Tricopter Photo6.jpg|600px|thumb|left]] | ||
- zip tie and connect speed controller | - zip tie and connect speed controller | ||
- Put the screws in a center piece and attach legs putting the gimbled leg in the center | - Put the screws in a center piece and attach legs putting the gimbled leg in the center | ||
- use shorter 1 1/4 inch screw on inside for gimbled leg | - use shorter 1 1/4 inch screw on inside for gimbled leg | ||
- attach so that the motors face down and the wires are accesable | - attach so that the motors face down and the wires are accesable | ||
- | - [[File:Kramers Tricopter Photo7.jpg|600px|thumb|left]] | ||
- connect wires together in middle using solder and speaker wire | - connect wires together in middle using solder and speaker wire | ||
- pigtail all negative and positive from the speed controllers | - pigtail all negative and positive from the speed controllers | ||
| Line 47: | Line 48: | ||
- cut and strip speaker wire | - cut and strip speaker wire | ||
- cut shrink wrap and solder wire red to red black to black | - cut shrink wrap and solder wire red to red black to black | ||
- | - [[File:Kramers Tricopter Photo8.jpg|600px|thumb|left]] | ||
- lighter for shrink wrap | - lighter for shrink wrap | ||
- combine all neg and wire to neg for final wire | - combine all neg and wire to neg for final wire | ||
| Line 59: | Line 60: | ||
- attach the top plate | - attach the top plate | ||
- I messed up the side I soldered the large wires and had to flip the legs to make the bottom plate the top | - I messed up the side I soldered the large wires and had to flip the legs to make the bottom plate the top | ||
- | - [[File:Kramer's Tricopter Photo11.jpg|600px|thumb|left]] | ||
- | - [[File:Kramers Tricopter Photo10.jpg|600px|thumb|left]] | ||
Revision as of 20:36, 31 January 2015
Kramer's Documentation at end of day one 1/31/15 Tricopter Build
- Legs
- sanded Legs
- Assemble Motors
- attach the bottom braket
- get counter sink side correct
- Attach 2 non-servo motors to legs
- opposite side of screw holes
- align wires with opening
- use small cutout to enclose wires within leg slot
- could glue
- zip tie in place
-
- Zip tie and connect speed control - will need to determine direction after build by running the motor and noting direction so don't make permanent
-
- drill and file 3D printed gimble mount - use a screw and glue the end to make gimble pivot
-
- use super glue - screw motor on 3D printed mount - may need to drill to fit - align wires away from base end
-
- Attach servo - use drill to reverse counter sink screw hole to get a flush connection - cut two edges of servo star to fit - ensure full range of motion and attach star to servo - superglue to gimble
-
- Attach gimble and servo to leg
- Found out I made a mistake in how the wires were aligned with cutout on leg
- inscrewed and screwed
- use zip ties
- used super glue for spacer after zip tie
-
- zip tie and connect speed controller
- Put the screws in a center piece and attach legs putting the gimbled leg in the center
- use shorter 1 1/4 inch screw on inside for gimbled leg - attach so that the motors face down and the wires are accesable
-
- connect wires together in middle using solder and speaker wire
- pigtail all negative and positive from the speed controllers - cut and strip black and red wires - cut and strip speaker wire - cut shrink wrap and solder wire red to red black to black
-
- lighter for shrink wrap - combine all neg and wire to neg for final wire - do the same for pos - don't forget skrink wrap(large) - Extend all control wires - only the white wire from the two legs without the gimble - all three from the gimble - leave about 4 inches past the hole through the center section to the top - takes a while; don't forget the shrink wrap - attach the top plate - I messed up the side I soldered the large wires and had to flip the legs to make the bottom plate the top
-
-
