Band Saw: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
Kent.durvin (talk | contribs) mNo edit summary |
||
| Line 15: | Line 15: | ||
The Band Saw uses a thin metal blade running in a continuous | The Band Saw uses a thin metal blade running in a continuous loop. It can be used to rip cut, cross cut, cut curves, and resaw. It is good for cutting curves. | ||
The following guidelines should be followed at all times. | |||
* Safety glasses must be worn and hearing protection is recommended. | * Safety glasses must be worn and hearing protection is recommended. | ||
| Line 28: | Line 30: | ||
Operational Safety Rules: | Operational Safety Rules: | ||
* Keep the blade guard 1/4” above the stock. | * Keep the blade guard 1/4” above the stock. | ||
* The blade alignment tracking should be at the center of the wheels. | * The blade alignment tracking should be at the center of the wheels, but not touching the guide bearings. | ||
* Make sure that the upper and lower wheel guard doors are closed when running. | * Make sure that the upper and lower wheel guard doors are closed when running. | ||
* Keep bystanders away from the right hand area of the saw. Broken blades have a tendency to fly out to the right or front. | * Keep bystanders away from the right hand area of the saw. Broken blades have a tendency to fly out to the right or front. | ||
Revision as of 21:54, 20 February 2019
Description: Grizzly G0555LX 14" Bandsaw
Location: Fab Lab
Safety: Manual
Tips
- Always use appropriate protective gear.
- Lower blade guard to approximately 1/4 inch above material.
- Ensure that blade has tension from the quick release lever.
- Remove tension after use with the quick release lever.
The Band Saw uses a thin metal blade running in a continuous loop. It can be used to rip cut, cross cut, cut curves, and resaw. It is good for cutting curves.
The following guidelines should be followed at all times.
- Safety glasses must be worn and hearing protection is recommended.
- Always keep fingers 3” from the blade.
- Check the blade tension and tracking before starting.
- Never use your thumbs to push toward the blade.
- Never back out of a curve cut while the machine is running.
- Don’t cut material that is not flat on the bottom without a jig.
- Remove loose fitting clothing, jewelry, and tie back long hair.
Operational Safety Rules:
- Keep the blade guard 1/4” above the stock.
- The blade alignment tracking should be at the center of the wheels, but not touching the guide bearings.
- Make sure that the upper and lower wheel guard doors are closed when running.
- Keep bystanders away from the right hand area of the saw. Broken blades have a tendency to fly out to the right or front.
- Always keep your fingers and hands away from the path of the blade.
- To control the stock, use push sticks, feather boards, or any other safety device when cutting small or short stock.
- Use a “V” block when cutting cylindrical stock.
- Cut at a moderate feed rate into the blade. Do not force a cut.
- Cut relief cuts prior to cutting long or tight curves.
- If you need to back out of a cut, shut the machine off, after blade stops, and then back out.
- If a blade breaks, shut the machine off and stand clear until everything stops.
- When cutting with the table at an angle, clamp a block to the table to prevent your stock from slipping off the table.
- Always disconnect the power before changing the blade or performing any other maintenance operation.
- Turn off the band saw and wait until comes to a complete stop. Never stick an object into the blade to stop the machine quicker. Let it stop on
its own.
Training Checklist
- Overview and Characteristics
- Theory of Operation
- Strengths
- Weaknesses
- Anatomy
- Safety
- Lower blade guard
- Allow machine to reach full speed
- Keep fingers out of the path of the blade
- Always wear eye and ear protection
- Operation
- Power
- Adjusting tension
- Adjust guide blocks
- Dust collection
- Apply and remove tension
- Rip Cut
- Cross Cut
- Cutting curves and relief cuts
- Angle cuts with tilted blade
- Change blade