CNC Training: Difference between revisions
Jump to navigation
Jump to search
Ranthalion (talk | contribs) Created page with "--- Work in Progress --- ==Goals of CNC training== CNC is all about processing gcode. The process is - #Design #Convert #Cut Design Options *Inkscape *TinkerCAD *Sketchup..." |
Ranthalion (talk | contribs) No edit summary |
||
| Line 1: | Line 1: | ||
--- Work in Progress --- | --- Work in Progress --- | ||
==Training Checklist== | |||
* Introduction/walk around | |||
** Dust Collection | |||
** Machine Bed | |||
** Router – Collets - Cutters | |||
** Gantry/Moving Parts | |||
** PC & Software Locations | |||
** Material Storage | |||
** Jogging control | |||
* Health & Safety Risks | |||
** Dust | |||
** Noise | |||
** Fire | |||
** Trapping | |||
** Burns | |||
** Loss of Limb or Digit | |||
* Safety Equipment | |||
** Ear Protection | |||
** Safety Goggles | |||
* Machine Startup & Positioning | |||
** Power on PC and start Mach3 | |||
** Power up main switch | |||
** Check dust collection is functional and not full | |||
* Job Setup – Demo piece | |||
** Workholding, Clamping and work positioning | |||
** Tool Selection & Collet sizes | |||
** Zero work | |||
** Load G-Code | |||
** Air cut | |||
** Turn on router and adjust speed | |||
** Dynamically adjust stepper speed rate | |||
'''''Do Not Leave The Machine Unattended While Running A Job!''''' | |||
==Goals of CNC training== | ==Goals of CNC training== | ||
Revision as of 19:42, 5 June 2015
--- Work in Progress ---
Training Checklist
- Introduction/walk around
- Dust Collection
- Machine Bed
- Router – Collets - Cutters
- Gantry/Moving Parts
- PC & Software Locations
- Material Storage
- Jogging control
- Health & Safety Risks
- Dust
- Noise
- Fire
- Trapping
- Burns
- Loss of Limb or Digit
- Safety Equipment
- Ear Protection
- Safety Goggles
- Machine Startup & Positioning
- Power on PC and start Mach3
- Power up main switch
- Check dust collection is functional and not full
- Job Setup – Demo piece
- Workholding, Clamping and work positioning
- Tool Selection & Collet sizes
- Zero work
- Load G-Code
- Air cut
- Turn on router and adjust speed
- Dynamically adjust stepper speed rate
Do Not Leave The Machine Unattended While Running A Job!
Goals of CNC training
CNC is all about processing gcode. The process is -
- Design
- Convert
- Cut
Design Options
- Inkscape
- TinkerCAD
- Sketchup
- AutoCAD
- Other CAD software
Convert
- gcodetools
- CAMBAM
- ???
Cut
- Mach3
- LinuxCNC
Using Mach3
- Pin/Port, motor, and GCODE configuration
- Jogging the machine
- Setting the home point
- Testing the cuts
- Changing the bits
- Dust collection
- Changing the speed
- Rewind/Reset
- The STOP button and limit switches
Preparing the machine
- NEVER move the motors manually while connected to control box - it can damage the electronics.
- Zero the spindle high above
- Test the gcode
- Zero the spindle for real
- Monitor the cut, adjusting speed as needed.
Preparing the workpiece
- double sided tape
- screws (and sanding smooth)
- clamps and dog holes?
- vacuum table would be cool
- dust control
- Leveling the table to the gantry
Common problems
- Run out
- Bad gcode
- Bad cuts - too fast, too dull, too deep
- wrong units (mm vs inches)
- wrong arc method (absolute vs relative)
- stuck limit switch
- cheap control box (prone to break or overheat?)
- watch out for obstructions (this also means screw and clamps)