3D Printing: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| Line 5: | Line 5: | ||
{| class="wikitable" style="text-align: center;" | {| class="wikitable" style="text-align: center;" | ||
! !!Prusa i3 | ! !!Prusa i3 MK2.5 | ||
! Ultimaker 3 | ! Ultimaker 3 | ||
! Form 1+ | ! Form 1+ | ||
|- | |- | ||
| align="left" | | | align="left" | | ||
|[[File:Prusai3mk2s_small.jpg]] | ||[[File:Prusai3mk2s_small.jpg]] | ||
||[[File:Ultimaker.png]] | ||[[File:Ultimaker.png]] | ||
|| [[File:form_1_plus.jpg|200px]] | || [[File:form_1_plus.jpg|200px]] | ||
|- | |- | ||
| align="left" | Number of Print Heads | | align="left" | Number of Print Heads | ||
||1 | ||1 | ||
|| 2 | || 2 | ||
|| 1 | || 1 | ||
|- | |- | ||
| align="left" | Build Platform Envelope | | align="left" | Build Platform Envelope | ||
||250 x 210 x 200 mm | ||250 x 210 x 200 mm | ||
||215 x 215 x 200 mm Single <br>197 x 215 x 200 mm Dual | ||215 x 215 x 200 mm Single <br>197 x 215 x 200 mm Dual | ||
|| 165 x 124 x 124 mm | || 165 x 124 x 124 mm | ||
|- | |- | ||
| align="left" | Heated Build Platform | | align="left" | Heated Build Platform | ||
|| Yes | || Yes | ||
|| Yes (20°C to 100°C) | || Yes (20°C to 100°C) | ||
|| no | || no | ||
|- | |- | ||
| align="left" | Filament Normally Loaded | | align="left" | Filament Normally Loaded | ||
| Line 40: | Line 40: | ||
|- | |- | ||
| align="left" | Nominal Print Speed | | align="left" | Nominal Print Speed | ||
|| 15 mmᶟ/s | || 15 mmᶟ/s | ||
|| 30 to 300 mm/s | || 30 to 300 mm/s | ||
|| 1-3 cm/hour Z Axis | || 1-3 cm/hour Z Axis | ||
|- | |- | ||
| align="left" | Resolution | | align="left" | Resolution | ||
|| 50 microns | || 50 microns | ||
|| 20 microns | || 20 microns | ||
|| 25 microns | || 25 microns | ||
|- | |- | ||
| align="left" | Typical Print Layer Thickness | | align="left" | Typical Print Layer Thickness | ||
|| | || | ||
|| | || | ||
|| 25 - 100 μm | || 25 - 100 μm | ||
|- | |- | ||
| align="left" | Printing Temperature | | align="left" | Printing Temperature | ||
|| | || | ||
|| | || 180–280° C | ||
|| | || 18–28° C | ||
|- | |- | ||
| align="left" | Web Site | | align="left" | Web Site | ||
| Line 64: | Line 64: | ||
|| [https://formlabs.com/ Form Labs] | || [https://formlabs.com/ Form Labs] | ||
|- | |- | ||
| align="left" | User Manual ||[ | | align="left" | User Manual | ||
|| [https://ultimaker.com/ | ||[https://www.prusa3d.com/downloads/manual/prusa3d_manual_mk25_en_2_51.pdf Manual] | ||
|| [https://support.formlabs.com/hc/en-us/categories/115000003004-Form-1-/ Manual] | || [https://support.ultimaker.com/hc/en-us/article_attachments/360010836740/Ultimaker_3_manual__En_.pdf Manual] | ||
|| [https://support.formlabs.com/hc/en-us/categories/115000003004-Form-1-/ Manual] | |||
|- | |- | ||
| align="left" | Hack.RVA Wiki | | align="left" | Hack.RVA Wiki | ||
|| | || | ||
||[[Ultimaker 3]] | ||[[Ultimaker 3]] | ||
|| [[Form 1+]] | || [[Form 1+]] | ||
|- | |- | ||
| align="left" | Firmware Version | | align="left" | Firmware Version | ||
||3. | ||3.10.1 | ||
||3. | ||5.3.0.0 | ||
|| N/A | || N/A | ||
|- | |- | ||
| align="left" | Serial No. | | align="left" | Serial No. | ||
||CZPX2817X003XK26782 | ||CZPX2817X003XK26782 | ||
||BPP-003840-027155 | ||BPP-003840-027155 | ||
|| Sassy Leveret | || Sassy Leveret | ||
|- | |- | ||
| align="left" | Software | | align="left" | Software | ||
|| Cura | || Cura | ||
|| Cura | || Cura | ||
|| Pre Form | || Pre Form | ||
|} | |} | ||
Revision as of 16:50, 8 January 2022
HackRVA has three 3D printers in residence: a Prusa i3 MK2, an Ultimaker 3 and a Form 1+. The Form1+ is a resin type 3d printer that uses a liquid photopolymer that is selectively hardened by a UV laser on the bottom of a clear tank. The makerspace usually has a selection of generic filament for occasional use. Members should provide their own filament if they are printing a large project or require a specific type.
Here’s a short comparison of the four printers:
| Prusa i3 MK2.5 | Ultimaker 3 | Form 1+ | |
|---|---|---|---|
|
|
| |
| Number of Print Heads | 1 | 2 | 1 |
| Build Platform Envelope | 250 x 210 x 200 mm | 215 x 215 x 200 mm Single 197 x 215 x 200 mm Dual |
165 x 124 x 124 mm |
| Heated Build Platform | Yes | Yes (20°C to 100°C) | no |
| Filament Normally Loaded | 1.75mm PLA, ABS, PETG | 3mm PLA, ABS, PETG | Photopolymer Resin |
| Nozzle Diameter | 0.40mm | 0.40 mm, 0.80 mm | 405 nm |
| Nominal Print Speed | 15 mmᶟ/s | 30 to 300 mm/s | 1-3 cm/hour Z Axis |
| Resolution | 50 microns | 20 microns | 25 microns |
| Typical Print Layer Thickness | 25 - 100 μm | ||
| Printing Temperature | 180–280° C | 18–28° C | |
| Web Site | Prusa | Ultimaker | Form Labs |
| User Manual | Manual | Manual | Manual |
| Hack.RVA Wiki | Ultimaker 3 | Form 1+ | |
| Firmware Version | 3.10.1 | 5.3.0.0 | N/A |
| Serial No. | CZPX2817X003XK26782 | BPP-003840-027155 | Sassy Leveret |
| Software | Cura | Cura | Pre Form |