3D Printing: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| Line 22: | Line 22: | ||
| align="left" | Build Platform Envelope | | align="left" | Build Platform Envelope | ||
||250 x 210 x 200 mm | ||250 x 210 x 200 mm | ||
|| | ||215 x 215 x 200 mm Single <br>197 x 215 x 200 mm Dual | ||
|| 165 x 124 x 124 mm | || 165 x 124 x 124 mm | ||
|- | |- | ||
| Line 33: | Line 33: | ||
|| 1.75mm PLA, ABS, PETG | || 1.75mm PLA, ABS, PETG | ||
|| 3mm PLA, ABS, PETG | || 3mm PLA, ABS, PETG | ||
|| | || Photopolymer Resin | ||
|- | |- | ||
| align="left" | Nozzle Diameter | | align="left" | Nozzle Diameter | ||
||0.40mm | || 0.40mm | ||
|| 0.40 mm, 0.80 mm | || 0.40 mm, 0.80 mm | ||
|| 405 nm | || 405 nm | ||
|- | |- | ||
| align="left" | Nominal Print Speed | | align="left" | Nominal Print Speed | ||
|| | || 15 mmᶟ/s | ||
|| 30 to 300 mm/s | || 30 to 300 mm/s | ||
|| 1-3 cm/hour Z Axis | || 1-3 cm/hour Z Axis | ||
|- | |||
| align="left" | Resolution | |||
|| 50 microns | |||
|| 20 microns | |||
|| 25 microns | |||
|- | |- | ||
| align="left" | Typical Print Layer Thickness | | align="left" | Typical Print Layer Thickness | ||
Revision as of 12:16, 25 September 2021
The hackRVA makerspace has five 3D printers in residence: a Prusa i3 MK2, an Ultimaker 3, an UP Mini, a da Vinci Pro, and a Form 1+. Form1+ is a different type of 3d printer: It uses a liquid photopolymer that is selectively hardened by a UV laser on the bottom of a clear tank. It is capable of much higher resolution.
The makerspace has a wide selection of filament. We try to keep some generic filament loaded for your occasional use. If you want something special, you can bring your own and load it.
Here’s a short comparison of the four printers:
| Prusa i3 MK2S | ! Ultimaker 3 | ! Form 1+ | |
|---|---|---|---|
| Photo | | 
|
|
|
| Number of Print Heads | 1 | 2 | 1 |
| Build Platform Envelope | 250 x 210 x 200 mm | 215 x 215 x 200 mm Single 197 x 215 x 200 mm Dual |
165 x 124 x 124 mm |
| Heated Build Platform | Yes | Yes (20°C to 100°C) | no |
| Filament Normally Loaded | 1.75mm PLA, ABS, PETG | 3mm PLA, ABS, PETG | Photopolymer Resin |
| Nozzle Diameter | 0.40mm | 0.40 mm, 0.80 mm | 405 nm |
| Nominal Print Speed | 15 mmᶟ/s | 30 to 300 mm/s | 1-3 cm/hour Z Axis |
| Resolution | 50 microns | 20 microns | 25 microns |
| Typical Print Layer Thickness | Coming Soon! | Coming Soon! | 25 - 100 μm |
| Printing Temperature | Coming Soon! | 180 ˚C to 280 ˚C | 15 ˚C to 30 ˚C |
| Web Site | Prusa | Ultimaker | Form Labs |
| User Manual | Manual | Manual | Manual |
| Hack.RVA Wiki | Write Me! | Ultimaker 3 | Form 1+ |
| Firmware Version | 3.0.12 | 3.7.7.20170627 | N/A |
| Serial No. | CZPX2817X003XK26782 | BPP-003840-027155 | Sassy Leveret |
| Software | Cura | Cura | Pre Form |